Bluegill - Big Bluegill

Do you love big bluegill?

Views: 539

Replies to This Discussion

This rotisserie motor is what I use to power my dryer.  I keep my poppers rotating until the finish dries/sets up other wise it will sag.   The pour-on in the picture has a real long pot time but takes a long time to set up, I will let it turn four to six hours and then let it dry overnight. It drys very clear and I haven't had any issues with tackiness after 24 hours.  As you can see it was very simple to construct the dryer. I cut 3 circles from scrap wood, the diameter was the same as a 12 ounce coke can, then drilled a hole in the middle of the circle then glued it to a dowell.  the foam came from an old coozie (canned drink insulator sleeve) and was slipped on and is easy to replace when it starts getting worn.  Commercial dryers turn a little faster than 1 RPM but this seems to do the  trick.

Great stuff mark thanks for sharing.

I have a rotsserie motor I use for various things, rods and occasionally bug, but it turns about 6 rpm's .  I have known of guys using the motor from microwave turntable for similar purposes, which I think are a little quieter than what I have experienced with rotisserie motors.  That looks like a very well designed and versatile setup you have there.

I used a microwave oven plate turner motor out of an old broke oven. It works just fine but I just have one disk attached for holding the poppers.

What a great idea, we have some great minds here.

here's my paint area. my dryer is in the back left.

sorry about the picture its the wrong one. I don't think it loaded anyway.

I guess the picture answered my question. Is that finish a polyurethane. Ive been using epoxys and haven't really found one that does what I want.

the finish pictured above is a 2-part epoxy "envirotex lite"

I have a friend that likes "BSI" two part epoxy that has a 30 minute cure time I think I will give that a try because some times I get tired of waiting for the "envirotex lite" to cure.  

Also popular for finish is a glue called "Liquid Fusion" with the added advantage of  no mixing required.

When I am playing around with a new design I will use uv light cured finish that dries almost instantly; but not practical if  you are doing 40 poppers at a time.

i think a product called liquid fusion is a good epoxy alternative.i think it also must be dried on a wheel

clever design John; very appealing to the eye!! bet you had no problem selling them!!  I sold my turner with a rod wrapper i built on craigslist last Saturday replaced it with a CRB rod turner that easily adapted to a fly dryer.  If I came across some motors like yours with those clean lines I would make a permanent turner dedicated only to fly tying.

RSS

Latest Activity

Jeffrey D. Abney posted a photo

Found a Few Hibiscus not Quite Bloomed…..7/5/2025

This is always a great spot with cypress, cattails and now a blooming hibiscus..next time I’m there…
18 hours ago
Jeffrey D. Abney commented on Jeffrey D. Abney's photo
Thumbnail

Fish Attractant in the Coastal N.C. Marsh…..7/4/2025

"Thanks John…anytime you get close to them there’s hundreds of different insects…"
18 hours ago
Jeffrey D. Abney posted a photo

Joe Struck Copper on a Sand Bar….7/5/2025

The wind was building on the main river so we splashed back to the ramp after 42 gills, 1 bullhead…
18 hours ago
John Sheehan commented on Jeffrey D. Abney's photo
Thumbnail

Fish Attractant in the Coastal N.C. Marsh…..7/4/2025

"Good work on finding fish habitat!"
18 hours ago
Jeffrey D. Abney posted a photo

Pretty Masked Copper Shallow ……7/5/2025

Preparing for next week’s buck moon on 7/10……
18 hours ago
Jeffrey D. Abney posted photos
18 hours ago
Jeffrey D. Abney posted photos
18 hours ago
Jeffrey D. Abney posted a status
"Up early this morning, heard we were going to have a tropical storm in the Carolina’s…so Joe and I went and burned some crickets…"
18 hours ago
Jeffrey D. Abney commented on Jeffrey D. Abney's photo
Thumbnail

Fish Attractant in the Coastal N.C. Marsh…..7/4/2025

"I have Bruce but most jigs I use are 1/32 or 1/16 with a little bigger hook…..with so many…"
18 hours ago
Bruce Tomaselli commented on Jeffrey D. Abney's photo
Thumbnail

Fish Attractant in the Coastal N.C. Marsh…..7/4/2025

"Smart plan. Do you fish any ant or grasshopper type jigs and bait?"
19 hours ago
Jeffrey D. Abney posted a photo

Fish Attractant in the Coastal N.C. Marsh…..7/4/2025

I search out these wild hibiscus flowers because they attract lots of insects which in turn brings…
yesterday
Jeffrey D. Abney commented on Jeffrey D. Abney's photo
Thumbnail

The Emerald Colors are Incredible……7/3/2025

"This one had it behind the eyes and the tail….."
yesterday
Jeffrey D. Abney commented on Jeffrey D. Abney's photo
Thumbnail

Emerald Tail Black Crappie……7/3/2025

"It may be a brackish water thing…..these fish are living in an area just a mile from dense…"
yesterday
Jeffrey D. Abney commented on Jeffrey D. Abney's photo
Thumbnail

Nice Channel Cat Grabbed the Jig Under a Float…..7/3/2025

"Anywhere you have food and a little current you have plenty of channel cat……had…"
yesterday
Jeffrey D. Abney commented on Jeffrey D. Abney's status
"Thanks John….I ran out of characters or I would have included the falling wind…"
yesterday
John Sheehan commented on Jeffrey D. Abney's status
"Good info!"
yesterday
John Sheehan commented on Jeffrey D. Abney's photo
yesterday
Bruce Tomaselli commented on Jeffrey D. Abney's photo
yesterday
Jeffrey D. Abney posted a photo

Emerald Tail Black Crappie……7/3/2025

You only get these markings right after the catch….they go dark in minutes…
yesterday
Jeffrey D. Abney posted photos
Thursday

© 2025   Created by Bluegill.   Powered by

Badges  |  Report an Issue  |  Terms of Service