Bluegill - Big Bluegill

Do you love big bluegill?

Some of the tools we need to tie flies are better bought, like a whip finisher (I haven't learned to whip finish by hand) or a bobbin.

However, my bodkin, bobbin threader, thingamajigger that twists a dubbing loop, and my dubbing brush are all hand-made.

For my bodkin, I went to Micheal's and bought a package of large needles from the quilting section.  I went over to the candy-making / baking department and bought a package of extra-large lollipop sticks.  I cut about 2" off the end of the 8" lollipop stick.  There is a small hole at the very center where the paper starts to get rolled up.  I just stuck the needle down there, pulled it out, put some glue on it, and shoved it back in.  Once it set, I was ready to go.

My bobbin threader is nothing but a length of 8 lbs test mono, pulled into a loop, then furled (twisted) for a couple inches.  I took the doubled mono and tied an overhand knot in it to secure the furling.  I just insert the loose ends into the bobbin until it hits the knot, poke the thread through the loop, then grasp the loose ends and pull it out, bringing the thread with it.

The "thingamajigger" is just a spare knob for a kitchen cabinet.  I cut a wire hanger, bent it into a "U" shape, then turned it sideways and bent the loop of the "U" at about a 160 degree angle to the long axis of the wire, forming a "tab" of sorts.  Finally, I bent the loose ends of the wire together, put some glue into the screw hole for the knob, and stuck the wire in there until it set.

My dubbing brush is extremely simple.  I bought a pack of craft sticks (popsicle sticks), and some plain velcro.  I cut a section of the "sticky" velcro to shape, and glued it to the end of a craft stick.  I can use that as a brush for dubbing after I dub a fly.

Anyone else have some homemade tools?

Views: 3775

Replies to This Discussion

I don't have any homemade tools. All I really have is a threader, a  bobbin, and a whip finishing tool, which I have yet to master. Your homemade tools seem to work well. I may make a dubbing brush like yours. I like the thought and satisfaction of using things I built. My next project is gonna be some rod holders for my little Bass Hunter boat. Trying to hold two poles yesterday, and run my tiller handle trolling motor yesterday proved to be a challenge. 

 the best bodkin i ever came up with is a pin vise.i have a couple different types .the advantage to these is you can easily replace the needle and use differet sizes or tiny drill bits to hand drill tiny holes.as soon as i get a new camera i will put some pics up

hehe - My dubbing brush is my old hearing aid brush and a piece of velcro on a strip of balsa wood.

yeah rick the velcro works great as a dubbing brush.antone ever make a dubbing brush twister?i remember seeing an article about making one.to premake bodies using wire instead of a thread loop

I remember reading about a tool you could put together to cut zonker strips.  It involves a long bolt, some washers for spacers, and razor blades that have a hole in them.  You alternate washers with razors, however many you want, on the bolt.  Keep it all together with a lock-nut.  Then you just run the pelt through it, similar to a paper-shredder, to cut the zonker strips.

I got some stuff together to assemble one.  I'm mainly interested in cutting some plastic strips for use as shellback material for scuds, but the possibility of cutting my own zonker strips is there as well.

Here is a link to what you were talking about - cutting you own zonker strips....... enjoy

 

http://globalflyfisher.com/tiebetter/zonkers/cutting.php

Thanks!  I hadn't thought to look for a video.  Obviously, I need another bolt and nut.  And, I was wondering how I was going to actually cut the things without slicing my hands all to heck.

I whip finish by hand because I can't seem to use a tool. My vise pedestal base is an old, large wood cutting board with a nutplate in it. The upright is a piece of broom handle with a lag bolt in one end that screws into the nutplate and a hole in the other to accept  the stem of the vise. It is slightly small to restrict unwanted movement. I also use a piece of heavy mono as a bobbin threader. My wifes used insulin syrenges make good applicators for head cement and other liquids. If one caps them the contents wil stay usable for a long time.

Great tips on tools Allen!!!!!! American ingenuity strikes again!!!!! Your dubbing brush is simple I"m sure but effective. I use a new gun cleaning brush , the military kind with small stiff bristles on one end and the larger longer ones on the other end. Works really good on dubbed Marabou , which I use a lot of for some of  Sir Jeffrey's bugs. For a bobbin threader I use just the plain old floss threader and works great. Got a 6 pack of em when I first started tying long ago and still have 4 of the original 6. They will for sure last longer than me!!!!

RSS

Latest Activity

John Sheehan commented on John Sheehan's status
"We are exploring/learning the three permit lakes late in life. Today was Canistear Reservoir. Hot…"
yesterday
John Sheehan posted a status
"Just dink smallmouths and Largemouth Bass for Greg and I, fishing a third Reservoir this year."
yesterday
John Sheehan posted photos
yesterday
Bruce Tomaselli commented on Jeffrey D. Abney's photo
Thumbnail

Sunrise Shellcracker…..7/23/2025

"I love your kind of fishing!"
Sunday
Jeffrey D. Abney commented on Jeffrey D. Abney's photo
Thumbnail

Sunrise Shellcracker…..7/23/2025

"I’m very fortunate that the fishing  in coastal North Carolina is so great and most…"
Sunday
Jeffrey D. Abney commented on John Sheehan's photo
Thumbnail

JULYWP

"Summer colors on this white perch!"
Sunday
Jeffrey D. Abney commented on John Sheehan's photo
Thumbnail

JULYP

"Nice Yellow John….good colors"
Sunday
Jeffrey D. Abney replied to Jeffrey D. Abney's discussion Panfish Species of North America- Which Ones Have You Caught?
"Often bass fisherman will catch Warmouth on 9” worms……..they. don’t fight…"
Sunday
Jeffrey D. Abney replied to Jeffrey D. Abney's discussion Panfish Species of North America- Which Ones Have You Caught?
"This is a great comparison John…..I added another photo to give perspective….."
Sunday
Bruce Tomaselli commented on Jeffrey D. Abney's photo
Thumbnail

Sunrise Shellcracker…..7/23/2025

"I sure envy you, enjoy!"
Sunday
John Sheehan replied to Jeffrey D. Abney's discussion Panfish Species of North America- Which Ones Have You Caught?
"Hey Jeffrey! Does the Warmouth have about the same sized Mouth as a Black Crappie of equal size, or…"
Saturday
Jeffrey D. Abney posted photos
Jul 23
Jeffrey D. Abney replied to Jeffrey D. Abney's discussion Panfish Species of North America- Which Ones Have You Caught?
"Some quality Warmouth I caught in my early years on the Albemarle….."
Jul 23
Jeffrey D. Abney replied to Jeffrey D. Abney's discussion Panfish Species of North America- Which Ones Have You Caught?
Jul 23
Jeffrey D. Abney replied to Jeffrey D. Abney's discussion Panfish Species of North America- Which Ones Have You Caught?
Jul 23
Jeffrey D. Abney posted photos
Jul 23
Jeffrey D. Abney replied to Jeffrey D. Abney's discussion Panfish Species of North America- Which Ones Have You Caught?
"Thanks for sharing John……you have patterned your available species pretty good over…"
Jul 23
John Sheehan replied to Jeffrey D. Abney's discussion Panfish Species of North America- Which Ones Have You Caught?
"Only caught five of these Species up here in New Jersey. Bluegill, Pumpkinseed, Red Breasted…"
Jul 23
Jeffrey D. Abney posted a photo

Crackers Saved This Morning Behind A Cold Front…..7/23/2025

If I get out the remainder of July it will probably be a crappie stalk on the coastal marsh……
Jul 23
Jeffrey D. Abney posted photos
Jul 23

© 2025   Created by Bluegill.   Powered by

Badges  |  Report an Issue  |  Terms of Service